AC Controllers For Sensicool Packaged AC, Air Conditioner Controllers, Manufacturer, Exporter, Supplier, Proton Power Control, Pune, Maharashtra, India

Sensicool Controller MODEL : AC-2-SC (1P),ACC09/02 (3P)



Available in Single and Three Phase
Image Shown is for Single Phase
1] Controls two air conditioners. 2] Separate Phase Supply fo r each A/C.
3] Bright Red 4 Digit LED Display.
4] Accurate Temperature sensing by precise temperature sensor.
5] Time Sharing for Compressors to share load equally.
6] Voltage & Current protections for each compressor.
7] Separate alarm relay contacts for AC Fail.
8] Fire protection by Digital Input
9] SPP, Reverse phasing protection for both AC1 & Ac2(In case of 3 Phase)
10] Hour counters for Compressor ON Period to check its reliability.
11] Display of all the A/C parameters & fault messages continuously in a scrolling manner.
12] Display Hold Feature by using ENTER Key. Press it again to release the hold.
13] Various set points are settable through the following different Menu categories:
a] VEW b] SET c] RESET
14]Password Protection for all the settings.
15] Sensor Fail Mode to keep ON & OFF cycle of one of the A/C through sensor fail ON/FF time settings.
16] Auto (with all protections)/Manual (without protection) Modes.
17] Controller Bypass feature by provision of Switch on Front Panel.
18] LED Indications to observe the status.

  • Supply Voltage (1P): 230 V AC, 50 Hz +/- 15% separate for each A/C.
  • Supply Voltage (3P): 415 V AC, 50 Hz +/- 15% separate for each A/C.
  • Contact Rating (1P): 30A at 230V AC for Compressor Power Outputs(Live) & 5A at 250 V AC for Alarm Potential Free Outputs(C,N,O)
  • Contact Rating (3P): 9A 3 Phase Contactor for Live outputs and 5A at 250 V AC for Alarm Potential Free Outputs(C,N,O)
    SPP, Reverse phasing protection for both AC1 & Ac2(In case of 3 Phase)
  • Temperature Sensor: Thermistor Sensor NTC 10K@25ºC Metal body with clamp. Sensor Cable Length: 2.75 meters
  • Temperature Sensing Range: 0.0 ºC to 55.C º
  • Resolution : 1V for Voltage, 0.1 A for Current & 0.1ºC for temperature.
  • Auto/Controller Bypass Switch: : To bypass the controller i.e. A/C1 & A/C2 will remain ON continuously if both the switches are in ON condition.
  • Indications:
    1) SupplyON for A/C1 & A/C2. Colour: Yellow
    2) Auto Mode for A/C1 & A/C2 Colour: Green
    3) Manual Mode for A/C1 & A/C2 Colour: Red
    4) AC ON for A/C1 & A/C2 Colour: Green
    5) Fault for for A/C1 & A/C2 Colour: Red
    6) Room High Colour: Red
    7) Healthy Colour: Green
  • Keys : :4 key keypad for setting
    1) Set Key
    2)Up (Arrow )Key
    3)Down( Arrow ) Key
    4)Enter Key

 

  • Controls two air conditioners.
  • Separate Phase Supply for each A/C.
  • Bright Red 4 Digit LED Display.
  • Accurate Temperature sensing by precise temperature sensor.
  • Time Sharing for Compressors to share load equally.
  • Voltage & Current protections for each compressor.
  • Separate alarm relay contacts for AC Fail.
  • Fire protection by Digital Input
  • Hour counters for Compressor ON Period to check its reliability.
  • Display of all the A/C parameters & fault messages continuously in a scrolling manner.
  • Display Hold Feature by using ENTER Key. Press it again to release the hold.
  • Various set points are settable through the following different Menu categories:
    a] VEW b] SET c] RESET 13]
  • Password Protection for all the settings.
  • Sensor Fail Mode to keep ON & OFF cycle of one of the A C Sthrough sensor fail ON/FF time settings.
  • Auto (with all protections)/Manual (without protection) Modes.
  • Controller Bypass feature by provision of Switch on Front Panel.
  • LED Indications to observe the status.

  • N/A


Download Brochure